asterisk dongle.conf

Asterisk

[general]

interval=15 ; Number of seconds between trying to connect to devices

;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
;jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a
; Dongle channel. Defaults to "no". An enabled jitterbuffer will
; be used only if the sending side can create and the receiving
; side can not accept jitter. The Dongle channel can't accept jitter,
; thus an enabled jitterbuffer on the receive Dongle side will always
; be used if the sending side can create jitter.

;jbforce = no ; Forces the use of a jitterbuffer on the receive side of a Dongle
; channel. Defaults to "no".

;jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.

;jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
; resynchronized. Useful to improve the quality of the voice, with
; big jumps in/broken timestamps, usually sent from exotic devices
; and programs. Defaults to 1000.

;jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a Dongle
; channel. Two implementations are currently available - "fixed"
; (with size always equals to jbmaxsize) and "adaptive" (with
; variable size, actually the new jb of IAX2). Defaults to fixed.

;jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set.
; The option represents the number of milliseconds by which the new jitter buffer
; will pad its size. the default is 40, so without modification, the new
; jitter buffer will set its size to the jitter value plus 40 milliseconds.
; increasing this value may help if your network normally has low jitter,
; but occasionally has spikes.

;jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------

[defaults]
; now you can set here any not required device settings as template
; sure you can overwrite in any [device] section this default values

context=from-trunk-dongle ; context for incoming calls
group=0 ; calling group
rxgain=0 ; increase the incoming volume; may be negative
txgain=0 ; increase the outgoint volume; may be negative
autodeletesms=yes ; auto delete incoming sms
resetdongle=yes ; reset dongle during initialization with ATZ command
u2diag=-1 ; set ^U2DIAG parameter on device (0 = disable everything except modem function) ; -1 not use ^U2DIAG command
usecallingpres=yes ; use the caller ID presentation or not
callingpres=allowed_passed_screen ; set caller ID presentation by default use default network settings
disablesms=no ; disable of SMS reading from device when received
; chan_dongle has currently a bug with SMS reception. When a SMS gets in during a
; call chan_dongle might crash. Enable this option to disable sms reception.
; default = no

language=en ; set channel default language
smsaspdu=yes ; if 'yes' send SMS in PDU mode, feature implementation incomplete and we strongly recommend say 'yes'
mindtmfgap=45 ; minimal interval from end of previews DTMF from begining of next in ms
mindtmfduration=80 ; minimal DTMF tone duration in ms
mindtmfinterval=200 ; minimal interval between ends of DTMF of same digits in ms

callwaiting=auto ; if 'yes' allow incoming calls waiting; by default use network settings
; if 'no' waiting calls just ignored
disable=no ; OBSOLETED by initstate: if 'yes' no load this device and just ignore this section

initstate=start ; specified initial state of device, must be one of 'stop' 'start' 'remote'
; 'remove' same as 'disable=yes'

exten=+1234567890 ; exten for start incoming calls, only in case of Subscriber Number not available!, also set to CALLERID(ndid)

dtmf=relax ; control of incoming DTMF detection, possible values:
; off - off DTMF tones detection, voice data passed to asterisk unaltered
; use this value for gateways or if not use DTMF for AVR or inside dialplan
; inband - do DTMF tones detection
; relax - like inband but with relaxdtmf option
; default is 'relax' by compatibility reason

; dongle required settings
[dongle0]
audio=/dev/ttyUSB1 ; tty port for audio connection; no default value
data=/dev/ttyUSB2 ; tty port for AT commands; no default value

; or you can omit both audio and data together and use imei=123456789012345 and/or imsi=123456789012345
; imei and imsi must contain exactly 15 digits !
; imei/imsi discovery is available on Linux only
;imei=123456789012345
;imsi=123456789012345

; if audio and data set together with imei and/or imsi audio and data has precedence
; you can use both imei and imsi together in this case exact match by imei and imsi required